Tests voltage, resistance, and continuity on igniters, flame sensors, control boards, and blower motors. It is how we confirm a part has actually failed before replacing it.
Furnace Repair in Severance that gets your heat back fast
When your furnace quits on a cold Weld County night, you need Furnace Repair in Severance you can count on. We diagnose the real problem, fix it with the right parts, and test every cycle before we leave.
Serving Severance and nearby areas.
How big is the furnace job?
Major component
Blower motor, control board, or inducer replacement with testing.
- 1. Single part Igniter, flame sensor, or thermocouple swap on an accessible furnace.
- 2. Major component Blower motor, control board, or inducer replacement with testing.
- 3. System level Heat exchanger or multi-component failures planned in writing first.
Drag the needle to compareTouch and drag the needle
- 24Services from one local team
- 15Areas served around Severance
- Test firstWe measure before we replace anything
- VerifyFull heat cycle before we leave
What a Furnace Repair visit covers
Every repair call includes a full diagnostic, the repair itself, and a test cycle to confirm the fix.
Work order
Furnace Repair- Full system diagnostic: We pull fault codes, test the igniter, flame sensor, gas valve, and blower with a multimeter and manometer. You get a clear explanation of what failed and why, not just a part number.
- The repair itself: Once you approve the price, we make the repair with the correct part. Igniters, thermocouples, flame sensors, capacitors, control boards, and blower motors are all common jobs we handle on site.
- Safety verification: We inspect the heat exchanger, test the flue for proper draft, and check for carbon monoxide risk. If we find something unsafe, we tell you before we leave and explain your options.
- Airflow and temperature check: After the repair, we verify the temperature rise is in spec and airflow is correct. A furnace that runs too hot or too cold will fail again, so we confirm it is dialed in.
- Filter and thermostat check: We check the filter and confirm the thermostat is calling correctly. A clogged filter or a miswired thermostat can mimic a furnace failure, and we rule those out as part of the visit.
What the first visit covers
First visit
We diagnose the fault, test the components, and explain what failed and what it takes to fix it.
Furnace repair at your home
We handle the furnace problems Severance homeowners call about most.
No heat
Furnace will not light or turn on at all
Cold air
Blowing cold air with the thermostat calling
Strange noises
Banging, rumbling, or squealing from the furnace
Short cycling
Runs a few minutes, shuts off, repeats
Furnace repair for Severance businesses
We service commercial heating systems and schedule around your business hours.
Retail spaces
Storefront and office furnace repair
Rental units
Multi-unit and landlord furnace service
Light commercial
Rooftop and split system repair
Furnace Repair in Severance, Colorado
A furnace repair done right the first time costs less than three guesses. We test, we measure, and we fix what actually failed. That is how you get heat back and keep it.
Furnace Repair in Severance is the diagnostic and repair work that gets a failed heating system safely running again, covering everything from a dirty flame sensor to a failed blower motor. Our techs test the igniter, thermocouple, control board, and gas valve, then confirm airflow and temperature rise before calling the job done. We work on Carrier, Trane, Goodman, Rheem, Lennox, Bryant, York, and American Standard equipment.
Severance winters swing hard, and furnaces here run long cycles from October through April. That wear shows up as short cycling, cold air at the registers, or a furnace that will not turn on at all. If you are searching for heater repair near me Severance, we cover emergency Furnace Repair in Severance CO and routine furnace service Severance CO with the same crew.
- What it is
- Diagnostic and repair work on a failed heating system
- When it helps
- No heat, cold air, strange noises, or short cycling
- What you get
- A tested repair and a furnace running to spec
What to expect on a repair call
From your first call to the final test cycle, here is how a Furnace Repair in Severance visit runs with our team.
Tools and methods we use on every call
Each method answers a different question. Together they leave very little to guess.
Measures gas pressure at the valve and manifold. Correct pressure is what keeps the burners running clean and the heat output where it should be.
Reads flue gas oxygen, carbon monoxide, and temperature. It tells us whether the furnace is burning safely and whether the heat exchanger is doing its job.
Confirms whether a standing pilot thermocouple is generating enough millivolts to hold the gas valve open. Common on older Severance furnaces.
Lets us look inside the heat exchanger and flue without tearing the furnace apart. It is how we confirm a crack instead of guessing.
When to call for furnace repair
Your furnace quit overnight and the house is down to 58 degrees by morning.
Call us first thing. We prioritize no-heat calls and can usually get a tech out the same day.
HomesYour furnace runs but never gets the house above 65 degrees, even with the thermostat set higher.
That points to airflow or temperature rise problems.
HomesYou smell gas near the furnace or your CO detector has gone off.
Leave the house and call us. We treat gas and CO calls as emergencies.
HomesYour furnace is 15 years old and has needed three repairs in the last two winters.
We inspect the heat exchanger and the major components, then give you honest numbers on repair versus replacement.
Homes
How Furnace Repair runs in Severance
Severance sits in Weld County, where winter temperatures regularly drop into the single digits and stay there for days. Furnaces here run long cycles from October through April, and that wear shows up fast.
Downtown Severance
Older homes with original ductwork and standing-pilot furnaces. We see a lot of thermocouple failures and undersized returns here.
Severance Farms
Newer construction with high-efficiency furnaces. Condensate line clogs and control board failures are the most common calls we get.
Weld County Road 74 corridor
Mix of rural and suburban homes on propane. Propane furnaces need different orifice sizing and more frequent burner cleaning.
- Downtown Severance
- Severance Farms
- Weld County Road 74 corridor
- Severance High School area
From problem to finished result.
Slide to compare the photo with an illustrative inspection view. It is generated from the photo, not a measurement.
PhotoNo-heat call fixed in one visit
Before: A Severance homeowner called at 7 a.m. with a furnace that would not light. The house was at 60 degrees and dropping. The thermostat was calling, but the burners never fired.
After: We diagnosed a failed igniter with a multimeter, replaced it with the correct part, and confirmed the burners lit on the first call. Temperature rise was back in spec at 45 degrees. Total time on site was 90 minutes.
Short cycling solved with airflow fix
Before: A Windsor homeowner said the furnace was running for two minutes, shutting off, then starting again. The house never got warm. The filter had not been changed in over a year.
After: We replaced the clogged filter, cleaned the blower wheel, and tested static pressure with a vacuum gauge. The furnace ran a full 15-minute cycle and hit the set temperature. No parts were needed.
Cracked heat exchanger caught early
Before: A Greeley landlord called about a furnace that smelled odd. The CO detector had not gone off, but the tenant was getting headaches. We inspected with a camera.
After: We found a cracked heat exchanger and documented it with photos. The furnace was unsafe to run. We walked the owner through replacement options and had a new unit installed within three days.
Common furnace problems we fix in Severance
Most no-heat calls come down to a handful of failures.
Furnace blowing cold air instead of heat
You are paying for gas or electric and getting nothing but a cold house.
Furnace will not turn on at all
No heat, no fan, nothing. In a Severance January, that turns into a real problem within hours, especially with kids or elderly residents in the house.
Furnace banging or rumbling noise
Banging usually means delayed ignition, where gas builds up before it lights.
Furnace leaking water
Water around the furnace usually means a clogged condensate line or a failed drain pan.
Why Severance homeowners call us first
We keep the diagnosis honest and the repair focused on what your system actually needs. Here is what that looks like on a real call.
Same-day heat restored
Most no-heat calls in Severance get diagnosed and repaired the same day.
Straight answers on cost
You get a clear price before we start.
Safety checked every visit
We inspect the heat exchanger, test for carbon monoxide risk, and verify the flue.
Local techs, local parts
Our techs know the equipment common in Severance and Weld County homes.
What you get on a repair job
Clear records you can keep and share.
Diagnostic findings
What failed and why, explained in plain terms
Parts record
Which part was replaced and the brand used
Test results
Temperature rise and airflow readings after the repair
Ten years fixing furnaces in Weld County
We have been repairing furnaces in Severance since 2016, and in that time we have worked on just about every brand and failure mode you can…
Fault codes
Read from the control board to point us at the failed component
Flame sensor microamps
Measured with a multimeter to confirm the sensor is reading the flame
Temperature rise
Compared against the manufacturer spec to confirm the furnace is running correctly
Are you in our Severance service area?
Type your ZIP or town to check. If yours is not listed, call and ask.
Severance ZIP codes
- 80650
- 80546
- 80550
- 80610
What Severance homeowners say
Our furnace quit on a Sunday night in January. They had a tech out by Monday morning, found a failed igniter, and had heat back on within an hour. The price was exactly what they quoted on the phone. I have already recommended them to two neighbors.
We had a furnace that was blowing cold air and short cycling. The tech tested everything with a meter, found a dirty flame sensor and a weak capacitor, and fixed both. He also showed me the filter was choked and walked me through changing it. Honest work.
I manage a few rentals and needed a furnace inspection on short notice. They came out, checked the heat exchanger with a camera, and gave me a written report I could hand to the owner. No upselling, just the facts. I use them for all my properties now.
Furnace repair questions we hear every week
Short answers for the first few minutes. The team can cover the rest.
Still have a question?
Describe what you are seeing and we will point you to the right next step.
(970) 1234567A flame sensor cleaning or igniter swap sits at the low end. A blower motor or control board replacement runs higher. We give you the price before we start, so there are no surprises.
We do. Severance Furnace Repair Pros has been servicing furnaces in Severance and Weld County since 2016. We handle gas, electric, and propane systems, and we work on all major brands. Call (970) 1234567 and we will get a tech out to you.
Yes, in most cases. We hold same-day slots for no-heat calls, and we prioritize emergency Furnace Repair in Severance CO when temperatures drop. Call before noon and there is a good chance we are at your door that afternoon. If we cannot make it same day, we tell you upfront.
The most common causes we see are a dirty flame sensor, a failed igniter, a bad capacitor, or a clogged filter choking airflow. Cold snaps and long run cycles wear those parts out faster. Less often, it is a faulty control board or a cracked heat exchanger, which is why we test before we replace anything.
Other heating services we handle
Other services from the same team.
- Furnace ReplacementWhen a cracked heat exchanger or a failed blower motor makes repair the wrong money, we size and…
- Furnace InstallationNew furnace installs for Severance homes, including gas line checks, flue connections and thermostat wiring.
- Emergency Furnace RepairEmergency hvac repair Severance CO homeowners call at 2 a.m. in January.
Get Furnace Repair in Severance before the next cold snap
(970) 1234567No heat is not something to wait on in a Colorado winter. Call Severance Furnace Repair Pros at (970) 1234567 and we will get a tech out to diagnose and fix your furnace.
Call for Furnace Repair in Severance
Call (970) 1234567 and describe what your furnace is doing. We answer, triage the symptom and give you a two-hour arrival window. Regular hours run 8 a.m. to 6 p.m. Monday through Friday, with emergency coverage for no-heat calls. If you are in ZIP 80650, 80546, 80550 or 80610, you are in our regular service area.