Tests voltage at the heating elements, continuity through the limit switch and sequencer, and control board output. It's the first tool out of the bag on every electric furnace call.
Electric Furnace Repair in Severance that gets your heat back on
When your electric furnace quits on a 15-degree Colorado night, you need Electric Furnace Repair in Severance that shows up and diagnoses the real problem.
Serving Severance and nearby areas.
How big is the repair?
Motor or board
Blower motor, control board, or element replacement with testing.
- 1. Single part One failed component like a limit switch, sequencer, or capacitor.
- 2. Motor or board Blower motor, control board, or element replacement with testing.
- 3. Multi-system Several failed components or airflow correction, planned in writing first.
Drag the needle to compareTouch and drag the needle
- 24Services from one local team
- 15Areas served around Severance
- Test firstWe measure before we replace
- Parts on truckCommon failures fixed in one visit
What's included in Electric Furnace Repair in Severance
Every electric furnace repair call includes a full diagnostic, a flat repair price you approve before we start, and a post-repair test cycle.
Work order
Electric Furnace Repair- Full electrical diagnostic: We test voltage at the heating elements, amp draw on the blower motor, continuity through the limit switch and sequencer, and control board output. This is where we find the actual failure instead of guessing at parts.
- Failed part replacement: Sequencers, limit switches, blower motors, capacitors, control boards, and heating elements are all covered. We use OEM or manufacturer-compatible parts and torque every electrical connection to spec before closing the panel.
- Safety circuit verification: After the repair, we test the high-limit circuit and confirm the limit switch isn't tripping. A furnace that runs past its safe temperature is a fire risk, so this step is non-negotiable on every job.
- Airflow and temperature check: We measure temperature rise at the supply and return, and check static pressure to confirm the blower is moving the right CFM. If airflow is restricted by a dirty filter or blocked duct, we tell you before it causes the next failure.
- Filter inspection and sizing: We check your furnace filter, note the correct size, and replace it if it's clogged. A dirty filter is the most common cause of electric furnace overheating, and it's a cheap fix that prevents expensive ones.
- Written repair summary: You get a written record of what failed, what we replaced, and any components we flagged as likely to fail next.
What the first visit covers
First visit
We test the elements, sequencer, limit switch, blower, and control board, then explain what failed and what it takes to fix it.
Electric furnace repair at your home
We handle electric furnace failures in houses across Severance and Weld County.
No heat at night
Priority dispatch when the furnace quits in cold weather.
Blowing cold air
We test elements and sequencer to find the failure.
Short-cycling furnace
Airflow and limit switch testing to stop the cycling.
Breaker keeps tripping
We isolate the circuit and find the shorted component.
Electric furnace repair for Severance businesses
We work around your operating hours to keep your space heated and your business running.
Retail and office
Scheduled repairs that don't disrupt business hours.
Light industrial
Heavy-duty electric furnace repair and documentation.
Rental properties
Turnover-window repairs with written records for owners.
Electric Furnace Repair in Severance, Colorado
Electric furnace repair is worth doing properly because a cheap fix on the wrong part just moves the failure down the road. We test the whole system, replace what actually failed, and verify it under load before we leave.
Electric Furnace Repair in Severance is the diagnostic and mechanical work that finds why an electric furnace stopped heating and returns it to safe, reliable operation. That means testing the heating elements, sequencer, limit switch, blower motor, capacitor, and control board with a multimeter and thermocouple tester, then replacing the failed component. Electric furnaces fail differently than gas units: no flame sensor or gas valve, but plenty of high-voltage contactors, relays, and element banks that burn out over time.
Severance sits in Weld County where winter nights drop below zero and the wind never seems to stop. Furnaces here run hard from October through April, and that constant cycling wears out sequencers, blower motors, and control boards faster than in milder climates. If you're searching for Electric Furnace Repair near me Severance CO because your system is blowing cold air or short-cycling, we can usually get a tech to your door the same day.
- What it is
- Diagnostic and repair work on electric furnace heating components.
- When it helps
- No heat, cold air, short-cycling, or breaker trips.
- What you get
- A working furnace and a written repair summary.
How our electric furnace repair process works
From the first call to the final test, here's exactly what happens when you book Electric Furnace Repair in Severance with us.
Tools and methods we use on every repair
Each method answers a different question. Together they leave very little to guess.
Verifies thermocouple and thermopile output on standing-pilot systems and hybrid furnaces. A weak thermocouple is a common reason a pilot won't stay lit.
Measures static pressure in the ductwork to confirm the blower is moving the right CFM. Restricted airflow is a leading cause of electric furnace overheating and short-cycling.
Used on gas and propane furnaces to verify combustion efficiency and check for carbon monoxide. Essential when a heat exchanger is suspect.
Reads flue gas composition on gas and propane systems to confirm proper combustion and venting. Part of every safety inspection we do.
When Severance homeowners call for electric furnace repair
Furnace dies on the first sub-zero night of the season, and the house drops below 60 degrees by morning.
We treat no-heat calls as priority, dispatch the nearest tech, and diagnose on arrival.
HomesFurnace runs constantly but the house never reaches the thermostat setting.
We check the heating elements, blower motor, and airflow.
HomesHome inspection before a Severance home sale flags the electric furnace as 'at end of life' with no specifics.
We do a full inspection: heat exchanger, elements, sequencer, limit switch, blower, and control board.
HomesFurnace trips the breaker every time it starts, and resetting it only works for a few minutes.
Breaker trips point to a shorted element, a failing blower motor, or a wiring issue.
HomesLandlord needs an electric furnace repaired at a rental property in Severance before new tenants move in.
We schedule around the turnover window, diagnose and repair in one visit when possible, and provide written documentation for the property file.
Businesses
How Electric Furnace Repair works in Severance
Severance sits at about 5,000 feet in Weld County, and that elevation changes how furnaces run. Air is thinner up here, so furnaces work harder to move the same CFM, and blower motors wear out faster than they do at sea level.
Severance Heights
Newer construction with tight building envelopes. Furnaces here are often slightly oversized for the ductwork, which causes short-cycling and premature limit switch failures.
Downtown Severance
Older homes with a mix of original electric furnaces and retrofitted systems. We see more wiring issues and undersized return ducts in this area.
Timber Ridge
Family homes with finished basements and zoned systems. Zoning problems often look like furnace failures, so we test the dampers and zone control board first.
- Severance Heights
- Downtown Severance
- Timber Ridge
- Severance Farms
From problem to finished result.
Slide to compare the photo with an illustrative inspection view. It is generated from the photo, not a measurement.
PhotoFailed sequencer on a January night
Before: A Severance homeowner called at 10 p.m. with no heat and the house already at 58 degrees. The furnace would click but never energize the elements. Our tech arrived at 11:15 p.m. and found a failed sequencer that wasn't passing voltage to the heating elements.
After: We replaced the sequencer with an OEM part from the truck, ran a full heating cycle, and confirmed 45 degrees of temperature rise at the supply.
Short-cycling fixed with airflow correction
Before: A Windsor homeowner had dealt with short-cycling for two winters. The furnace ran 3 minutes, shut off, and repeated. A previous company replaced the thermostat with no improvement. Our tech measured static pressure and found the return duct was undersized and the filter was clogged.
After: We replaced the limit switch that had been tripping, corrected the filter size, and adjusted the blower speed to match the ductwork. Temperature rise dropped from 65 degrees to 42 degrees, and the furnace now runs full cycles without tripping.
Blower motor replacement on a 15-year-old Carrier
Before: A Greeley rental property had a Carrier electric furnace with a blower motor that was drawing 12 amps instead of the rated 8. The motor was overheating, the furnace was shutting down on the high-limit switch, and tenants had been without reliable heat for a week.
After: We replaced the blower motor and capacitor, cleaned the blower wheel, and verified amp draw at 7.8 amps. The furnace ran a full 20-minute heating cycle without tripping, and the tenants had consistent heat for the rest of the winter.
Electric furnace problems we fix in Severance
Electric furnaces fail in predictable ways, and most of those failures show up as one of these symptoms.
Furnace blowing cold air
A furnace blowing cold air usually means the heating elements aren't energizing, the sequencer has failed, or the limit switch has tripped and won't reset.
Furnace won't turn on at all
A completely dead furnace in January is an emergency. Causes range from a tripped breaker to a failed control board to a bad thermostat.
Furnace banging or rattling noise
Banging and rattling usually point to a failing blower motor, a loose blower wheel, or a ductwork issue.
Furnace short-cycling
A furnace that turns on and off every few minutes isn't heating your home efficiently, and it's wearing out the sequencer and limit switch with every…
Furnace leaking water
Water around an electric furnace usually means a clogged condensate drain or a humidifier issue, not a furnace failure.
Why Severance homeowners call us first
Electric furnace problems get worse in the cold. Here's what you get when you call our team instead of waiting it out.
Same-day service
Most calls in Severance, CO get a technician the same day, and we run emergency electric heater repair in Severance through the coldest nights…
Upfront pricing
You get the diagnostic fee and the repair cost before we start.
All major brands
We service Carrier, Trane, Goodman, Rheem, Lennox, Bryant, York, and American Standard electric furnaces.
Code-correct work
We test the limit switch and high-limit circuit after every fix, because a furnace that runs past its safe temperature is a fire risk.
What you receive
Clear records you can keep and share.
Written findings
A summary of what failed and what we replaced.
Test results
Temperature rise and airflow readings from the repair.
Filter note
The correct filter size and condition noted for you.
10 years of electric furnace experience in Weld County
Severance Furnace Repair Pros has been fixing furnaces in Weld County since 2016.
Amp draw
We read blower motor amps and compare to the rated spec to catch a failing motor before it seizes.
Temperature rise
Supply minus return temperature tells us if the furnace is heating within its designed range.
Static pressure
We measure duct pressure to confirm the blower is moving enough air for the system.
Are you in our Severance service area?
Type your ZIP or town to check. If yours is not listed, call and ask.
Severance ZIP codes
- 80650
- 80546
- 80550
- 80610
What Severance homeowners say
Our electric furnace quit on a Friday night in January. Called at 9 p.m., tech was here by 11. Turned out to be a failed sequencer, and he had one on the truck. I've used two other HVAC companies in Weld County and neither one would come out after hours without charging double.
We'd been dealing with a furnace that short-cycled for two winters. First company replaced the thermostat, didn't fix it. Severance Furnace Repair Pros found a failing limit switch in about 20 minutes. Replaced it, tested the whole cycle, and it's been running clean since. Should have called them first.
I manage a dozen rentals across Weld County and use these guys for all my electric furnace calls. They show up when they say, give me a flat price before starting, and don't try to sell a replacement on every job. That last part matters when you're paying the bill on 12 properties.
Frequently Asked Questions
Short answers for the first few minutes. The team can cover the rest.
Still have a question?
Describe what you are seeing and we will point you to the right next step.
(970) 1234567A limit switch or sequencer replacement sits at the low end; a blower motor or control board pushes toward the top. The diagnostic fee is disclosed upfront, and you approve the repair price before we start work.
Severance Furnace Repair Pros handles electric furnace repair across Severance, Weld County, and the surrounding towns. We work on all major brands including Carrier, Trane, Goodman, Rheem, Lennox, Bryant, York, and American Standard.
The most common causes we see in Severance are a failed sequencer, a tripped limit switch, a burnt-out heating element, or a bad blower motor. Sometimes it's as simple as a tripped breaker or a thermostat set to fan-only. Electric furnace troubleshooting in Severance, Colorado starts with a multimeter check at the elements and a continuity test through the safety circuit.
Yes. If your furnace quits on a cold night, call (970) 1234567 and we'll dispatch the nearest available tech. Most emergency calls in Severance get a response within a few hours.
Related Services
Other services from the same team.
- Commercial Furnace RepairRooftop and shop-unit furnace service for Severance businesses and Weld County shops.
- Propane Furnace RepairPropane furnaces run hotter and sootier than natural gas, so we check the heat exchanger and burner orifices…
- Furnace MaintenanceAnnual maintenance that catches dirty flame sensors, worn capacitors and clogged filters before they strand you in a…
Get Electric Furnace Repair in Severance before the next cold snap
(970) 1234567No heat is not something to wait out. Upfront pricing, parts on the truck, and a repair that holds through a Weld County winter.
Call for Furnace Repair in Severance
Call (970) 1234567 and describe what your furnace is doing. We answer, triage the symptom and give you a two-hour arrival window. Regular hours run 8 a.m. to 6 p.m. Monday through Friday, with emergency coverage for no-heat calls. If you are in ZIP 80650, 80546, 80550 or 80610, you are in our regular service area.