Serving Severance and nearby areas
Furnace Repair Severance CO for No-Heat Nights
Furnace Repair Severance CO means a tech at your door with a multimeter and a combustion analyzer, not a sales pitch. We diagnose no-heat calls, furnace blowing cold air, and short-cycling systems across Weld County, then fix what is actually broken.
- 24Services from one local team
- 15Areas served around Severance
- Test firstMeter and combustion readings before any quote
- Plain notesWhat failed, why, and what it costs
Furnace Repair Severance CO Built on Real Diagnostics
We pull the burner cover, meter the igniter and flame sensor, then read flue gas before quoting. You see the failed part and the price before we start. After the repair we run a full heat cycle and re-check the readings.
Parts on the truck
Common igniters, sensors and capacitors stocked
Photos of the fault
You see the cracked part before we swap it
Filter size logged
Written on the cabinet for next time
Furnace Repair and hvac repair Severance Services
One truck, one call, and the full range of furnace work: repair, replacement, tune-ups, safety inspections and brand-specific service.
Furnace Repair
Diagnostic-first repair for no-heat calls, short cycling and weak airflow.
Furnace Replacement
When a cracked heat exchanger or a failed blower motor makes repair the wrong money, we size and swap the unit.
Furnace Installation
New furnace installs for Severance homes, including gas line checks, flue connections and thermostat wiring.
Emergency Furnace Repair
Emergency hvac repair Severance CO homeowners call at 2 a.m. in January. No heat with a house full of kids is not a wait-until-Monday problem.
Gas Furnace Repair
Gas valve testing, pilot and ignition faults, and combustion analysis with a flue gas analyzer.
Electric Furnace Repair
Heating element, sequencer and capacitor failures on electric furnaces. We meter each element and the blower circuit, then replace only what tests bad.
What the first call covers
- What you are seeing
- Furnace make and model
- When it started
- Whether it runs at all
- Photos of what we find
- Readings written down
- Old parts left with you
- Full cycle before we leave
Why Furnace Repair Severance CO Homeowners Call Us
We are not the biggest shop in Weld County, and that is the point.
-
Diagnostics before quotes
Every call starts with a multimeter, a manometer and a combustion analyzer. We meter the igniter, test the flame sensor and check gas pressure before we quote a repair.
-
Parts on the truck
We stock igniters, thermocouples, flame sensors, capacitors, control boards and common blower motors for Carrier, Trane, Goodman, Rheem, Lennox, Bryant, York and American Standard.
-
Ten years in Weld County
Severance Furnace Repair Pros has worked this area since 2016. We know how propane systems behave on the rural edges of town and how hard the dust hits blower wheels out here.
How Our Furnace Repair Calls Run
From the first phone call to the final combustion check, here is what to expect when you book furnace work with us in Severance.
-
Step 1
Call and triage
You describe the symptom: no heat, cold air, banging noise or a furnace that will not turn on.
-
Step 2
Test and diagnose
The tech meters the igniter, checks the flame sensor, reads gas pressure with a manometer and runs a combustion analysis. You get the failed part named and the repair price before any work starts.
-
Step 3
Repair and verify
We replace the failed component, then run the furnace through a full cycle. Temperature rise, amp draw and flue readings get checked again.
-
Step 4
Walkthrough and log
Before we leave, you get a plain-language rundown of what failed and why, plus the filter size and schedule for your unit. Any follow-up parts we had to order get scheduled on the spot.
Furnace Problems We Fix in Severance
Most furnace calls fall into a handful of patterns, and we have seen all of them in Weld County homes. Here is what we find and how we fix it.
Furnace blowing cold air with the thermostat calling for heat
- What we do
- Cold air usually means the burners are not lighting or the blower is running without flame. We test the igniter and flame sensor first, then check the gas valve and limit switch.
- Call right away if
- The air stays cold after ten minutes with the thermostat calling.
Furnace will not turn on at all, no fan and no heat
- What we do
- A dead furnace is often a control board, a blown capacitor or a tripped limit switch. We read the board, meter the low-voltage circuit and test the blower.
- Call right away if
- Nothing happens at all, no fan and no click.
Banging, rumbling or popping noise from the furnace
- What we do
- Banging on startup points to delayed ignition, and rumbling often means a dirty burner or a failing inducer. We clean the burners, check gas pressure with a manometer and test the inducer amp draw.
- Call right away if
- The bang happens on every startup, not just once.
Furnace leaking water on the floor near the unit
- What we do
- Water around a high-efficiency furnace is usually a clogged condensate line or a cracked drain pan. We clear the trap, check the slope and verify the line drains.
- Call right away if
- Water is spreading past the base of the furnace.
Pilot light will not stay lit on an older furnace
- What we do
- A pilot that keeps going out is almost always a weak thermocouple or a dirty pilot orifice. We test the thermocouple, clean the assembly and confirm a stable flame.
- Call right away if
- The pilot goes out within minutes of relighting.
Furnace Repair Service Area Around Severance
Severance sits between Windsor and Eaton in Weld County, and our trucks run the whole corridor.
Schematic only. Not to scale.
Eaton
View area EatonTimnath
View area TimnathLoveland
View area LovelandJohnstown
View area JohnstownMilliken
View area MillikenFurnace Repair Severance CO Questions
The questions we get most on the phone, answered straight. If yours is not here, call and we will talk it through.
Still have a question?
Describe what you are seeing and we will point you to the right next step.
(970) 1234567The right shop is the one that tests before it quotes. Ask whether they use a combustion analyzer and an inspection camera, whether the diagnostic fee is credited toward the repair, and whether they stock common parts for your brand.
Yes. No-heat calls do not wait for business hours, and neither do we. If your furnace quits at 2 a.m. in a January cold snap, call (970) 1234567 and we triage the situation on the phone. Emergency calls get priority scheduling, and we bring the common failure parts so most emergency visits close in one trip.
Check three things: whether they diagnose with real instruments instead of guessing, whether they quote the repair before starting, and whether they carry parts for your furnace brand. A tech who meters the igniter and reads flue gas will find the actual fault. One who skips straight to a replacement quote is selling, not repairing.
Yes, and it covers the whole Weld County corridor, from Severance out to Windsor, Eaton and Greeley. Emergency calls get triaged on the phone so we know what parts to load. If you smell gas or see soot around the furnace, leave the house and call from outside before anything else.
Get Furnace Repair Severance CO Before the Next Freeze
(970) 1234567No heat is not a wait-and-see problem in a Colorado winter.
Call for Furnace Repair in Severance
Call (970) 1234567 and describe what your furnace is doing. We answer, triage the symptom and give you a two-hour arrival window. Regular hours run 8 a.m. to 6 p.m. Monday through Friday, with emergency coverage for no-heat calls. If you are in ZIP 80650, 80546, 80550 or 80610, you are in our regular service area.